Tripp Lite Fiber Optic 10/100/1000 to 1000BaseLX SC Gigabit Multimode Media Converter 2km 1310nm - fiber media converter
$175.00
$121.69
Mfg # N785-001-SC
CDW # 2028049
| UNSPSC 26121607
Quick tech specs
- Fiber media converter
- 10Base-T, 1000Base-FX, 100Base-TX, 1000Base-T
- up to 1.2 miles
- 1GbE
- RJ-45 / SC
- 1310 nm
Know your gear
Tripp Lite's N785-001-SC 10/100/1000 Gigabit Multimode Media Converter is an economical way to extend the distance ( up to 2Km ) of network nodes by converting Cat5/6 UTP cables to Fiber Optic. With advanced features such as selectable half or full duplex operation on the fiber port, 1310 nm wavelength, automatic MDI/MDI-X configuration and link fault pass-through, the N785-001-SC supplies superior signal quality and gives you ultimate network control. The N785-001-SC is compatible with both 62.5/125 and 50/125 multimode fiber cable.
Add to Compare
Enhance your purchase
Tripp Lite Gigabit Fiber Optic Media Converter UTP Ethernet to Fiber Optic is rated5.00 out of5 by3.
Rated 5 out of 5 byRW from OutstandingI had been trying to get a 1Gb media converter that would work on a fiber run. Tried numerous other brands/models and none would do it. This one did and has been very reliable. Outstanding product that just works!
Date published: 2015-02-23T00:00:00-05:00
Rated 5 out of 5 byjose sanchez from exellente producti like this media converter wokrs fine on my fibre optic this equipment install on two plant in Reynosa, México and no problem its really easy to install recomend this media converter on your IT room thanks
Date published: 2016-02-24T00:00:00-05:00
Rated 5 out of 5 byJim from 3rd Set we've purchased, totally pleasedPrior to Tripp Lite we had been using another brand, that was about half the cost of the Tripp Lite, however the previous devices were failing with 12-15 months. We have had two Tripp Lite devices in place now for two and one half years with no issues. Will keep buying Tripp Lite!
Date published: 2019-06-14T00:00:00-04:00
Rated 5 out of 5 byMOFIZZLE from Good device but read specs betterI bought these because we got a backup 100Mbps ethernet P2P circuit and the provider will only give us copper 100Mbps handoff unless we pay a lot more for the gig optical handoff same speed. Our equipment on both ends only support 1gig or 10gig SFP.This is a good device but the description it misleading. It says multimode fiber but if you read more detail you will see that it's optical wavelength is 1310nm which is long-range and can be used on single mode or multimode fiber. You will need to connect to a long range tansceiver like the GLC-LH-SM or similar.This device will not work with the shortrange GLC-SX-MM or similar short range transceivers which is 850nm.Also Tripplite only supports when the devices are connected directly to eachother over the Fiber ports using an SC-SC cable and the end devices connect to the copper ports. However It does work in reverse when converting from 2 fiber end devices with copper in between the 2 tripplite units but not supported by the Mfg. Also it does work when the device is used to convert gig-optical handoff from a provider to an end device that only has gig copper but again it's not supported by tripplite and the provider must use a Long-range transceiver.
Date published: 2014-03-19T00:00:00-04:00